To keep the car running normally, the broken ignition key needs to be repaired. The ignition switch needs a specific key to be replaced, which is always misplaced, leaving you with few alternatives. However, the key can also be replaced. Where do things go? Let’s see how to replace the keyless ignition switch.
Replacing The Ignition Switch
The ignition switch is one of the most critical aspects of the car, as it enables the normal operation of the vehicle’s main electrical circuit. Simply put, it is responsible for starting the engine.
Since the ignition key has the same impact on the car’s appliances, including the radio and power windows, it is important to keep the switch on. Therefore, a failure or malfunction of the ignition switch can prevent the car from running. This ensures that the engine will take a long time or not run at all.
The faulty ignition switch should be removed as soon as possible for the sake of vehicle protection. Since the struggle to start the car can affect or even kill the batteries.
The ignition key is located on the side of the steering wheel or on the dashboard column. The broken switch must be removed and replaced with a new one. It is easy to do this with the ignition switch key.
Each ignition switch comes with a unique key that only works on that switch. What if you lose it? Don’t worry, you can adjust it even if you don’t have the switch. Now let’s get down to business and see if we can do it:
How To Remove Ignition Lock Cylinder Without Key
To change the ignition switch on a keyless car, first, remove the ignition switch and then follow the normal steps for changing the ignition switch. So let’s get started:
Step 1: Disconnect Battery
The first phase of this guide is to remove the battery, open the hood and look for the battery. You will see that the battery is held together by a series of positive and negative clamps held together by a nut.
Remove only the negative clamp by loosening the nut with a wrench. It is not necessary to disconnect the positive cable. To avoid interference with the battery, keep the negative cable as far away from the battery as possible.
Step 2: Expose The Ignition Switch
The next step is to remove the decorative strip around the steering, exposing the ignition switch. Be careful not to scratch the decorative strips. To ensure proper disassembly, refer to the vehicle owner’s manual.
If the steering gear interferes with the direction of the ignition switch, it should also be disabled. This move is very helpful, especially if you do not have a wrench and may need to use a drill later. To easily separate the steering gear, you may need to use a steering wheel puller (depending on the vehicle model).
You will then uncover an ignition box, and the ignition key will remain in the panel. If it is sealed by a plastic sheet, release the clip before removing the cover.
Step 3: Removal of the ignition switch
Now comes the important part: the ignition switch must be uninstalled. As you may already know, disassembling an ignition switch usually requires the use of a wrench. However, you can also use drill bits, screwdrivers, and paper clips.
To begin with, use an electric drill to make a hole in the key slot of the car’s ignition cylinder. You should drill it large enough to allow for the insertion of a screwdriver.
Now, use whatever you have on hand to clean the dirt out of the hole. Next, take a paper clip and straighten it out. Place the clip in the hole and then on the left side of the ignition key lock cylinder. The ignition cylinder will not start as a result of this.
Next, using a screwdriver, insert it into the cavity and press it into the other side of the paper clip. This indicates that you can move the screwdriver to the right before it reaches the top.
Take the screwdriver and the clip simultaneously, and then slide the power switch out of place. In this way, you will be able to remove the switch without clicking. Then move on to the next step.
Step 4: Installation of a New Ignition Switch
You’ve almost ruined the ignition key by scratching and digging, but you’ll have to replace it. Don’t worry, the old one will be obsolete. Buy a new one that’s compatible with your car.
Pick up the last ignition switch and look in your hand for a pin. The release pin prevents the twist from extending.
In either situation, retain the pin and move the switch toward the ignition module slowly. To validate the location, wait for a click. If you do not get the twist out, try again.
Everything will be finished when you actually get the placement. Then move on to the next step.
Step 5: Testing the Switch
It is a good idea to inspect the ignition switch before reassembling everything, just in case the last ignition switch does not work properly. Although it would complete the circuit.
Since you have removed the cable from the negative terminal of the car battery, you should reconnect it with caution. Now that power has been restored, stick the key in the ignition switch and try to start the engine.
The job is complete if you can start the vehicle without problems. Replace the trim and steering wheel, then sit back and enjoy the ride.
How to Remove Ignition Lock Cylinder Chevy Without Key
Starting the engine is important. The Chevrolet ignition lock cylinder contains pins and tumblers, and the key is used to start the engine. These pins wear out over time, and the cylinder lock will no longer be able to unlock where the key is inserted.
The key inside the ignition switch may break or jam at the “ignition” point. Chevy describes these measures in depth.
To get started, you’ll need to use resources such as power drills, screwdriver heads, robotic gloves, screwdrivers, and socket wrench packs.
1. Disconnect the negative terminal of the battery.
Disconnect the negative cable from the car battery. This reduces the possibility of an electric shock. If there is an airbag, disconnect it. Disconnect the electrical connection of the airbag.
2. Remove the Cover
To remove the steering column cover, use a screwdriver and socket wrench. Remove the dashboard panel and insert the ignition key.
3. Remove Electrical Connections
The electrical connections of the ignition switch must be disconnected. Loosen the ignition switch screw. Loosen the ignition switch parts and housing.
4. Check Bolts
Examine the housing bolt heads and separate the ignition switch bolts with a power tool.
5. Reinstall all
Maintain the ignition switch assembly and ignition key lockout switch in a ready state. Install the new components on the vehicle steering column and ignition key assembly.
Place the ignition key in the vehicle before installing the ignition switch to verify the location of the lock cylinder. Reconnect the negative battery cable to the electrical linkage, start the engine and evaluate the ignition switch.
If the crank turns correctly, the column and airbag panels can be reconnected.
How to Remove Ignition Lock Cylinder without Key Ford
To begin, gather the following tools: a 10 mm wrench, a #2 Philips screwdriver, a socket wrench, and an 8-inch screwdriver, a utility knife, a small screwdriver, a spatula, a small paper clip, a small flathead screwdriver, a vise, pliers, needle-nose pliers, etc.
Step 1: Remove the Negative Terminal
Remove the negative terminal of the battery. You could be operating near the airbag. Remove also the airbag, so you would be operating near it, which may cause injury.
Disassembly of the airbag system will take some time because the capacitors must be discharged.
Step 2: Remove the covers
Remove the dashboard and steering wheel covers to access the ignition lock cylinder. Loosen the clamp, then gently remove the lower dash cover.
Remove the steering wheel lever and upper steering column cover. Pull down and sort the screws for quick replacement.
Step 3: Insert the key
Insert the key and turn it with a small screwdriver. The cylinder will slide out when you pull the key handle. Turn the key a little more and then press the screwdriver.
Be careful when removing the cylinder. Keep the order of the pins or marbles. Pull each of the black locking rings away from the lock cylinder.
Step 4: Check
Remove the matching tumbler from the current lock and reconfigure it to match the initial switch. Use the old matching cylindrical tumblers. Close the new tumblers and reassemble the cylinder.
To find the slot, insert the key. Remove the key and consider changing the cylinder.
If it does not turn without a key, it means it is done.
How to Remove Ignition Lock Cylinder without Key Dodge
Step 1: Unlock the Ignition Lock.
The ignition lock is mounted on the steering column and is held in place by movable positioning pins. Thus, to remove the movable pin from the column, the movable pin must be pushed in to unlock the ignition lock.
Step 2: Remove the Plastic from the Steering Column
The ignition lock can be kept “on”, and at the same time, the movable positioning pin should be pushed. If there are no vital means, you must do a thorough test to keep the car lock at the “on” point. Remove the plastic from the steering column secured by the screw until you reach the movable repair pin.
After removing the plastic column, you will see the electrical switches and locks. The lock opens when you press the movable bracket.
Step 3: Check
The active locator can be seen after cutting the lock and switch. Turn the lock to the ON position and be sure to hold down the movable retainer before detaching the lock from the button.
Conclusion
As a result, even if you don’t have a key, you now know how to change the ignition switch on a vehicle. This awesome trick is simple enough for even a novice car mechanic to do. Don’t pass up the opportunity to use this simple trick the next time your ignition switch fails.
